Linterna Convoy T3, alto CRI, linterna AA 14500, XPG2 219B 219C LH351D 519A 13 grupos

Parameter: LED : XPG2 R70 / 219B R9080 / 219C R9050 / 519A R9080 FLUX: 300-500lm Mode: 13groups ,Max current output 0.5A (AA battery),Max current output 1.5A (14500 lithium battery), Mode memory: yes Maximum efficiency: 75%(4modes)/90%(13groups) Battery: 1 * AA / 14500 (not included) Lighting range: less than 50meters Material: aluminum alloy Color : red/orange/blue/purple Waterproof grade: IPX6 Switch type: reverse Reflector type: orange peel Lens : normal glass Size: 21mm(diameter) ,93.3mm(length) Weight:47g (only flashlight ,not include the clip/lanyard/package) Accessory: 1*clip,1*lanyard Drive parameters 1. The flashlight is powered by a 1.5V battery or a 4.2V lithium battery. Switch the flashlight on or off by the tail switch (full click) or switch mode (Half-press). The maximum output current is 0.5A when using a 1.5V battery, and the maximum output current is 1.5A when using a 4.2V lithium battery 2. Battery judgment function: When the voltage is above 2V, it is judged as a 4.2V battery, and when the voltage is below 2V, it is a 1.5V battery. It does not turn on when powered on by 2-2.8V. 3. Low voltage protection. When using a 4.2V battery, the voltage will flash 3 times slowly when the voltage is lower than 3V, and it will automatically shut down when the voltage is lower than 2.8V. When using a 1.5V battery, there is no low voltage protection. At 4.2V, strobe (100%), slow flashing (30%), beacon (30%), battery detection (1%) SOS (20%), the above is the maximum brightness ratio. if flashlight is turned on,tap the switch 20 times quickly to enter into config mode.(On a visual interface,as long as you click on an option, it means that the option is selected. The flashlight has no visual interface. It flashes to represent an option, and "tap the switch in the flashing process" means to select the option.) Option 1 (normal-flash 1 time + buzz-flash): tap the switch to enter into sub-option to select the mode group,If the user has no operation, the config mode will enter option 2. -------------sub-option 1.1 (normal-flash 1 time) : tap the switch to select mode group 1 (1%、10%、30%、100%) -------------sub-option 1.2 (normal-flash 2 times) : tap the switch to select mode group 2 (1% 10%、35%、100%、strobe、biking、batcheck) -------------sub-option 1.3 (normal-flash 3 times) : tap the switch to select mode group 3 (100%、35%、10%、1%) -------------sub-option 1.4 (normal-flash 4 times) : tap the switch to select mode group 4 (1% 20%、100%、strobe、biking、batcheck) -------------sub-option 1.5 (normal-flash 5 times) : tap the switch to select mode group 5 (1%、20%、100%) -------------sub-option 1.6 (normal-flash 6 times) : tap the switch to select mode group 6 (100%、20%、1%) -------------sub-option 1.7 (normal-flash 7 times) : tap the switch to select mode group 7 (1% 10%、50%、strobe、biking、batcheck) -------------sub-option 1.8 (normal-flash 8 times) : tap the switch to select mode group 8(1%、10%、50%) -------------sub-option 1.9 (normal-flash 9 times) : tap the switch to select mode group 9 (50%、10%、1%) -------------sub-option 1.10 (normal-flash 10 times) : tap the switch to select mode group 10 (20%、100%) -------------sub-option 1.11 (normal-flash 11 times) : tap the switch to select mode group 11 (100%、20%、strobe) -------------sub-option 1.12 (normal-flash 12 times) : tap the switch to select mode group 12(100%) Option 2 (normal-flash 2 times + buzz-flash): tap the switch to active the mode memory or inactive it,If the user has no operation,flashlight will enter into the last mode. battery-checkinstructions: <2.95V1 flash, 2.95-3.25V2 flashes, 3.25-3.55V3 flashes, 3.55-3.85V4 flashes, >3.85V5 flashes Notice that there is no battery-check function if flashlight is powered by the 1.5V battery